How to maintain the Wire edm wear parts?

Wear is one of the most common and most numerous failure modes of a machine. No matter what product is produced, the parts which are in contact with each other during operation will be friction due to the relative motion, and the wear is due to the result of friction. Even to get the rapid development and widely application of electrical discharge machining (EDM) also wear, EDM method although can adapt to the needs of the development of production and in the application shows many excellent properties, but also can not avoid emergence of the wire EDM wear parts. It is precisely because of wear and tear caused by the loss of surface layer material, the size of the parts changed, directly affect the service life of parts. Therefore, in the production process, in time for the maintenance of the spark machine is very important, and that how to maintain the wire edm wear parts? Here to make a brief introduction of spark machine maintenance knowledge.
Maintenance can be divided into routine maintenance, mechanical parts to the first level maintenance, mechanical parts, such as two maintenance. Here to talk about the daily maintenance, that is, one day to maintain, of course, do not go to work on weekends to maintain.
    A day can be divided into before work, work, work in the maintenance:
1 before work:(1) check the buttons and switches, buttons, etc., the requirements of flexible and reliable, accurate location;(2) check the safety device, fastening device, the requirements of accurate, flexible, reliable, no loose;(3) check all kinds of instruments, the requirements of the correct, sensitive;(4) check the oil level, oil or grease lubrication chart according to the road, the amount of oil to meet the requirements;(5) the execution engine operation, each part should fully exercise and lubrication. 
2 work:;(1) the implementation of operational procedures, to strictly abide by(2) at any time to listen, look, touch, smell, observe the operation of equipment, to timely treatment, without trouble running.
3 after work:(1) cleaning chip, wipe the appearance, the taper hole of the main shaft and the sliding surface, more than three days not to anoint rust, to strictly abide by.(2) each moving parts, buttons and switches in a reasonable position to strictly comply with;(3) cut off the power supply and air source, must be strictly observed;(4) clean up the environment around the machine tool, without obstacles.
   Weekend
Weekend maintenance:Wipe all parts (including the operation of the panel, buttons, etc.), check the cleaning and filtering device, according to the slip table, while adding coolant to check whether the loosening of fasteners. Cleaning of spindle hole. Must be strictly abide by these.
   Regular maintenance of the spark machine is equivalent to maintenan the wire edm wear parts, so that it can delay the use of the wire edm wear parts, so it is very important to understand the know ledge of the Wire EDM Wear Parts,.What's more ,if you want to know more of the EDM Accessories knowledge could login KENOS official website .
yizeklc
Above article from KENOS official website (http://www.edm-accessories.com/
The original address:http://www.edm-accessories.com/1.html

评论

发表评论

此博客中的热门博文

What you need to know about wire cutting equipment

As we all know,  wire cutting equipment  is one of the most used machining equipment in the machinery manufacturing industry. Therefore, for friends engaged in wire cutting, the long-term benefits lie in the good use of wire cutting equipment, and whether to maintain it. 1.Introduction of wire cutting equipment WEDM was first invented in the former Soviet Union in 1960, but China was the first country to use it in industrial production. The instantaneous high temperature produced by electric spark can be corroded by local metal melting and oxidation. Wire cutting machine is invented on the basis of this principle, so it belongs to mechanical equipment in the field of electrical processing. 2.What are the components of the wire cutting equipment? The wire cutting equipment consists of three parts: mechanical, electrical, and working hydraulic system. 3.How to improve the machining efficiency of  WEDM equipment ? Cutting efficiency is affected by two main factors, one is the curre
阅读全文

Mixed Bed Ion Exchange Resins wholesale, choose KENOS Hardware Technology Co., Ltd.

图片
KENOS Hardware Technology Co., Ltd. is a wholesale Wire edm wear parts, EDM spare parts manufacturers, the main wholesale products are  Mixed Bed Ion Exchange Resins , conductive blocks, diamond wire guides, EDM filters and so on. Mixed Bed Ion Exchange Resins For Wire Cut EDM Machines is a kind of special ion exchange resin which has been regenerated and premixed and can be used directly. It is mainly used for the production of ultra-pure water in the water treatment system containing radioactive materials, semiconductor preparation and other industries. It can also be used for the refinement after various water treatment processes. Direct use without pretreatment and regeneration. Our Mixed Bed Ion Exchange Resins meet the technical specifications of the national and industrial standards. Similar products abroad: Dower MR-3, Amberlite UP-6150. Recommended operating conditions for Mixed Bed Ion Exchange Resins: 1.PH                                                    1-14 2.Maximum us
阅读全文

KENOS helps you solve common problems in WEDM

We always encounter some  Common problems in WEDM . So, how to solve these common problems in WEDM? Today, KENOS will help you solve them. 1.In the wire cutting process, the workpiece suddenly cut can not move how to do? This situation usually occurs when cutting hard-to-process materials such as stainless steel with high thickness. The fundamental reason is that the working fluid does not have good characteristics of erasing products. The emergency method is to add some detergent or increase the concentration of the working fluid, but the most fundamental way is to change the  EDM Fluid . 2.Molybdenum wire forward and backward cutting speed is inconsistent, or even do not go in one direction? This situation is often encountered in high thickness cutting, the root cause is still the problem of working fluid, but also related to the uniform consistency of frequency tracking speed and molybdenum wire tension. Therefore, when cutting high thickness workpieces, it is necessary to speed
阅读全文