Main technologies and methods of MITSUBISHI WEDM-LS equipment maintenance

There will be a variety of problems in the process of using the MITSUBISHI WEDM-LS equipment, which requires us to master the correct technologies and methods to repair and maintain them.
The main technologies and methods of MITSUBISHI WEDM-LS equipment maintenance are as follows:
1.In situ rush repair technology
Mitsubishi slow walking wire will inevitably be used in the process of failure or damage, in this case,the need for in-situ repair technology.In situ repair technology can enable it to recover its function in time and continue to use it.
2.Condition maintenance of equipment
Condition based maintenance is a commonly used method in the maintenance of mechanical equipment.This maintenance method needs to use the sensory ability and maintenance experience of equipment maintenance personnel to observe the operation of equipment,find out the abnormal characteristics of equipment in time,and select the appropriate means of detection and maintenance to repair equipment .
3.Fixed point maintenance technology 
At present,the development of material science in China is relatively fast,which creates favorable conditions for the improvement of maintenance level of Mitsubishi slow wire.
Above is the Main technologies and methods of MITSUBISHI WEDM-LS equipment maintenance.Actually,buy original and high quality MITSUBISHI EDM spare parts will reduce damage to MITSUBISHI WEDM-LS equipment.At the same time,in daily work should also pay attention to maintain MITSUBISHI WEDM-LS ,so that production efficiency will be greatly improved.
yize13ka
Above article from KENOS official website:(http://www.edm-accessories.com/)
The original address:(http://www.edm-accessories.com/55.html)

评论

发表评论

此博客中的热门博文

What you need to know about wire cutting equipment

As we all know,  wire cutting equipment  is one of the most used machining equipment in the machinery manufacturing industry. Therefore, for friends engaged in wire cutting, the long-term benefits lie in the good use of wire cutting equipment, and whether to maintain it. 1.Introduction of wire cutting equipment WEDM was first invented in the former Soviet Union in 1960, but China was the first country to use it in industrial production. The instantaneous high temperature produced by electric spark can be corroded by local metal melting and oxidation. Wire cutting machine is invented on the basis of this principle, so it belongs to mechanical equipment in the field of electrical processing. 2.What are the components of the wire cutting equipment? The wire cutting equipment consists of three parts: mechanical, electrical, and working hydraulic system. 3.How to improve the machining efficiency of  WEDM equipment ? Cutting efficiency is affected by two main factors, one is the curre
阅读全文

Mixed Bed Ion Exchange Resins wholesale, choose KENOS Hardware Technology Co., Ltd.

图片
KENOS Hardware Technology Co., Ltd. is a wholesale Wire edm wear parts, EDM spare parts manufacturers, the main wholesale products are  Mixed Bed Ion Exchange Resins , conductive blocks, diamond wire guides, EDM filters and so on. Mixed Bed Ion Exchange Resins For Wire Cut EDM Machines is a kind of special ion exchange resin which has been regenerated and premixed and can be used directly. It is mainly used for the production of ultra-pure water in the water treatment system containing radioactive materials, semiconductor preparation and other industries. It can also be used for the refinement after various water treatment processes. Direct use without pretreatment and regeneration. Our Mixed Bed Ion Exchange Resins meet the technical specifications of the national and industrial standards. Similar products abroad: Dower MR-3, Amberlite UP-6150. Recommended operating conditions for Mixed Bed Ion Exchange Resins: 1.PH                                                    1-14 2.Maximum us
阅读全文

KENOS helps you solve common problems in WEDM

We always encounter some  Common problems in WEDM . So, how to solve these common problems in WEDM? Today, KENOS will help you solve them. 1.In the wire cutting process, the workpiece suddenly cut can not move how to do? This situation usually occurs when cutting hard-to-process materials such as stainless steel with high thickness. The fundamental reason is that the working fluid does not have good characteristics of erasing products. The emergency method is to add some detergent or increase the concentration of the working fluid, but the most fundamental way is to change the  EDM Fluid . 2.Molybdenum wire forward and backward cutting speed is inconsistent, or even do not go in one direction? This situation is often encountered in high thickness cutting, the root cause is still the problem of working fluid, but also related to the uniform consistency of frequency tracking speed and molybdenum wire tension. Therefore, when cutting high thickness workpieces, it is necessary to speed
阅读全文