Common faults and Solutions of WEDM equipment

In the process of using WEDM equipment, due to improper operation or other reasons, will lead to its failure, even if a small failure, will also cause delays in production, then what is a good solution? Today, KENOS will tell you some common faults and solutions of WEDM equipment.
Fault 1: when the boot button is activated, the laser cutting machine does not move.
When this situation occurs, we need to check whether the WEDM equipment is powered on, if not, please plug in the power supply; check its motherboard parameters are correct, if not, please refer to the software instructions to correct parameters.
Fault 2: No laser in operation.
Check if the light path is offset, refer to the light path adjustment; if there is a problem with the line, then you can insert the point ray with the WEDM equipment into the signal terminal of the power supply to determine.
Fault 3: unstable light.
Check the water circulation is unobstructed, if not unobstructed please clean the water tank and pump, dredge the water pipe; check the power supply voltage is stable at this time, if the voltage is unstable, Please add a voltage regulator to the power supply.
Fault 4: WEDM equipment can not process online data.
Check whether the communication data line is connected, if not, shut down and reconnect the data line; software USB is installed successfully, if the installation fails, please reinstall the software and USB driver.
Above are four kinds of WEDM equipment common faults and their solutions, KENOS reminds everyone that in the process of processing, we must always pay attention to the operation of WEDM equipment a variety of matters needing attention. At the same time, we also need to replace the oldEDM spare parts regularly. If you have any questions, you can consult us, because we are a professional manufacturer of EDM spare parts.
yize17ka
Above article from KENOS official website:(http://www.edm-accessories.com/)
The original address:(http://www.edm-accessories.com/91.html)

评论

发表评论

此博客中的热门博文

What you need to know about wire cutting equipment

As we all know,  wire cutting equipment  is one of the most used machining equipment in the machinery manufacturing industry. Therefore, for friends engaged in wire cutting, the long-term benefits lie in the good use of wire cutting equipment, and whether to maintain it. 1.Introduction of wire cutting equipment WEDM was first invented in the former Soviet Union in 1960, but China was the first country to use it in industrial production. The instantaneous high temperature produced by electric spark can be corroded by local metal melting and oxidation. Wire cutting machine is invented on the basis of this principle, so it belongs to mechanical equipment in the field of electrical processing. 2.What are the components of the wire cutting equipment? The wire cutting equipment consists of three parts: mechanical, electrical, and working hydraulic system. 3.How to improve the machining efficiency of  WEDM equipment ? Cutting efficiency is affected by two main factors, one is the curre
阅读全文

Mixed Bed Ion Exchange Resins wholesale, choose KENOS Hardware Technology Co., Ltd.

图片
KENOS Hardware Technology Co., Ltd. is a wholesale Wire edm wear parts, EDM spare parts manufacturers, the main wholesale products are  Mixed Bed Ion Exchange Resins , conductive blocks, diamond wire guides, EDM filters and so on. Mixed Bed Ion Exchange Resins For Wire Cut EDM Machines is a kind of special ion exchange resin which has been regenerated and premixed and can be used directly. It is mainly used for the production of ultra-pure water in the water treatment system containing radioactive materials, semiconductor preparation and other industries. It can also be used for the refinement after various water treatment processes. Direct use without pretreatment and regeneration. Our Mixed Bed Ion Exchange Resins meet the technical specifications of the national and industrial standards. Similar products abroad: Dower MR-3, Amberlite UP-6150. Recommended operating conditions for Mixed Bed Ion Exchange Resins: 1.PH                                                    1-14 2.Maximum us
阅读全文

KENOS helps you solve common problems in WEDM

We always encounter some  Common problems in WEDM . So, how to solve these common problems in WEDM? Today, KENOS will help you solve them. 1.In the wire cutting process, the workpiece suddenly cut can not move how to do? This situation usually occurs when cutting hard-to-process materials such as stainless steel with high thickness. The fundamental reason is that the working fluid does not have good characteristics of erasing products. The emergency method is to add some detergent or increase the concentration of the working fluid, but the most fundamental way is to change the  EDM Fluid . 2.Molybdenum wire forward and backward cutting speed is inconsistent, or even do not go in one direction? This situation is often encountered in high thickness cutting, the root cause is still the problem of working fluid, but also related to the uniform consistency of frequency tracking speed and molybdenum wire tension. Therefore, when cutting high thickness workpieces, it is necessary to speed
阅读全文