Do you know how to deal with the disconnection of MITSUBISHI EDM wire?

In our processing process, mechanical equipment will always appear a variety of problems. How to solve these problems is the concern of many operators. So, do you know how to deal with the disconnection of MITSUBISHI EDM wire? Today, KENOS, a supplier of Wire edm wear parts, gives you a brief analysis.
First of all, when the disconnection of MITSUBISHI EDM wire occurs, it is necessary to check whether the tensile strength of the wire is abnormal; whether there is a bad wiring situation. Then check whether the conductive block is damaged. If there is any damage, new conductive blocks should be replaced immediately. Check whether the processing fluid is imbalance of yin and Yang impurities, processing water and temperature should be controlled.
At the same time, do a good job of preventive measures, also can reduce the problem of Mitsubishi wire breakage. Regular inspection of clean guide wire to prevent blockage; timely replacement of aging or damaged parts, which can effectively reduce the disconnection of MITSUBISHI EDM wire.


If you need to buy Mitsubishi or other brands of Wire edm wear parts, welcome to choose Dongguan KENOS hardware Technology Co., Ltd., we provide various high-quality EDM accessories, products after strict quality inspection process, looking forward to working with you.
yize19ka
Above article from KENOS official website:(http://www.edm-accessories.com/)
The original address:(http://www.edm-accessories.com/106.html)

评论

发表评论

此博客中的热门博文

What you need to know about wire cutting equipment

As we all know,  wire cutting equipment  is one of the most used machining equipment in the machinery manufacturing industry. Therefore, for friends engaged in wire cutting, the long-term benefits lie in the good use of wire cutting equipment, and whether to maintain it. 1.Introduction of wire cutting equipment WEDM was first invented in the former Soviet Union in 1960, but China was the first country to use it in industrial production. The instantaneous high temperature produced by electric spark can be corroded by local metal melting and oxidation. Wire cutting machine is invented on the basis of this principle, so it belongs to mechanical equipment in the field of electrical processing. 2.What are the components of the wire cutting equipment? The wire cutting equipment consists of three parts: mechanical, electrical, and working hydraulic system. 3.How to improve the machining efficiency of  WEDM equipment ? Cutting efficiency is affected by two main factors, one is the curre
阅读全文

Mixed Bed Ion Exchange Resins wholesale, choose KENOS Hardware Technology Co., Ltd.

图片
KENOS Hardware Technology Co., Ltd. is a wholesale Wire edm wear parts, EDM spare parts manufacturers, the main wholesale products are  Mixed Bed Ion Exchange Resins , conductive blocks, diamond wire guides, EDM filters and so on. Mixed Bed Ion Exchange Resins For Wire Cut EDM Machines is a kind of special ion exchange resin which has been regenerated and premixed and can be used directly. It is mainly used for the production of ultra-pure water in the water treatment system containing radioactive materials, semiconductor preparation and other industries. It can also be used for the refinement after various water treatment processes. Direct use without pretreatment and regeneration. Our Mixed Bed Ion Exchange Resins meet the technical specifications of the national and industrial standards. Similar products abroad: Dower MR-3, Amberlite UP-6150. Recommended operating conditions for Mixed Bed Ion Exchange Resins: 1.PH                                                    1-14 2.Maximum us
阅读全文

KENOS helps you solve common problems in WEDM

We always encounter some  Common problems in WEDM . So, how to solve these common problems in WEDM? Today, KENOS will help you solve them. 1.In the wire cutting process, the workpiece suddenly cut can not move how to do? This situation usually occurs when cutting hard-to-process materials such as stainless steel with high thickness. The fundamental reason is that the working fluid does not have good characteristics of erasing products. The emergency method is to add some detergent or increase the concentration of the working fluid, but the most fundamental way is to change the  EDM Fluid . 2.Molybdenum wire forward and backward cutting speed is inconsistent, or even do not go in one direction? This situation is often encountered in high thickness cutting, the root cause is still the problem of working fluid, but also related to the uniform consistency of frequency tracking speed and molybdenum wire tension. Therefore, when cutting high thickness workpieces, it is necessary to speed
阅读全文